Adafruit

This 2x20-pin strip male header is a great way to add pins to 2x20 0.1" holes in a PCB.  They're also perfect companion piece to our 2x20-pin righ...

A great mini HDMI to HDMI plug.  We find this plug adapter really helpful.  It's a great way to convert any mini HDMI plug to a normal HDMI plug a...

This tiny 1" diameter speaker cone is the perfect addition to any small audio project where you need an 8 Ω impedance and will be using 0.5W or les...

The cable is easiest way ever to connect to your microcontroller/Raspberry Pi/WiFi router serial console port. Inside the big USB plug is a USB<...

Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. There are ...

This nifty little plastic tool provides you a super simple, super cheap means for adjusting the lens of your Raspberry Pi camera! Simply place the ...

This is the assembled version of the Pi T-Cobbler Plus.   It works with all modern Pi boards released after 2014 (A+, B+, 2, 3, 4, etc)This Cobbler...

Make your own USB connections without slicing apart a USB cable and soldering those thin wires inside. These DIY "USB shells" are available in USB ...

Connect two HDMI devices together and save space with this basic flat HDMI 1.4 cable. It has nice molded grips for easy installation, and is 1 foot...

These are standard '130 size' DC hobby motors. They come with a wider operating range than most toy motors: from 4.5 to 9VDC instead of 1.5-4.5V. T...

PIR sensors are used to detect motion from pets/humanoids from about 20 feet away (possibly works on zombies, not guaranteed). This one has an adju...

This is a 'full-size' breadboard, 830 tie points. Good for small and medium projects. It's 2.2" x 7" (5.5 cm x 17 cm) with a standard double-strip ...

Hey want to hear a really loud noise? Apply 3V to 5V to this buzzer module and you'll be rewarded with a loud 2KHz BEEEEEEEEEEEEEEEEEP. Unlike a pl...

We now carry an assembled version with pre-installed headers Feather is the new development board from Adafruit, and like it's namesake it is thin,...

This enclosure was designed by Mike Doell - just like Adafruit's Pi Case for Raspberry Pi Model B.  Made of ultra-durable, super-glossy polycarbon...

This super small mono amplifier is surprisingly powerful - able to deliver up to 2.5 Watts into 4-8 ohm impedance speakers. Inside the miniature ch...

Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambient temperature. To use, connect pin 1 (left) t...

This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. Wh...

Handy for making wire harnesses or jumpering between headers on PCB's. These premium jumper wires are 3" (75mm) long and come in a 'strip' of 40 (4...

This fully-assembled pan-tilt kit is the perfect way to give your project full range motion with two micro servos. The pan-tilt can rotate roughly ...

Add a good quality, slim keyboard to your Raspberry Pi, Beagle Bone Black or other mini-computer with this sleek black chiclet keyboard. It's a ful...

Our all-in-one 5V 2.5 Amp + MicroUSB cable power adapter is the perfect choice for powering single-board computers like Raspberry Pi, BeagleBone or...

The Adafruit Pi Plate makes it easy to use a blue and white 16x2 Character LCD. Some 16x2 LCDs do require quite a few digital pins, 6 to control t...

Little clicky switches are standard input "buttons" on electronic projects. These work best in a PCB but can be used on a solderless breadboard as ...