Skip to content
We are able to ship once again, and are processing orders.
Please note that USPS is experiencing service delays. You may find more info at:

https://about.usps.com/newsroom/service-alerts/

Thank you for your patience!
We are able to ship once again and are processing orders. Please note that USPS is experiencing service delays. You may find more info at: https://about.usps.com/newsroom/service-alerts/ Thank you for your patience!

HyperPixel 4.0 Square - Hi-Res Display for Raspberry Pi

SKU CED-PIM475
Original price $88.99 - Original price $97.95
Original price
$88.99
$88.99 - $97.95
Current price $88.99
Title: Non-Touch

A uniquely square, high-resolution, high-speed, 4.0" display  for Raspberry Pi – it's hip to be square! Available in both touch and non-touch versions!

HyperPixel 4.0 Square has all the great features of our standard HyperPixel 4.0—a crisp, brilliant IPS display and high-speed DPI interface—it's just more square!

This square version of HyperPixel 4.0 is great for custom interfaces and control panels, and works really well for Pico-8 games. Everything is pre-soldered and ready to go, just pop it onto your Pi, run our installer, and away you go!

Note that the images of the displays on this page have not been Photoshopped. That's the Raspbian desktop with our HyperPixel Square wallpaper on!

Features

  • High-speed DPI interface
  • 4.0" IPS (wide viewing angle, 160°) display (72x72mm)
  • 720x720 pixels (~254 PPI)
  • 18-bit colour (262,144 colours)
  • 60 FPS frame rate
  • 40-pin female header included to boost height for Pi B+, 2, 3, 3B+ and 4
  • Standoffs included to securely attach to your Pi
  • Compatible with all 40-pin header Raspberry Pi models
  • One-line installer
  • Optional capacitive touchscreen

HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720x720px) on its 4.0" display. The display can show 18-bits of colour (262,144 colours).

The touchscreen variant is capacitive touch, that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch!

Please note: when installing HyperPixel 4.0 Square onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). Also take care not to pull on the edges of the glass display when removing your HyperPixel.

It'll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you're using it with a larger Pi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Pi Zero or Pi Zero W then just pop it straight onto the GPIO.

The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your Pi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your Pi.

Software

Find the GitHub repository here: https://github.com/pimoroni/hyperpixel4


Raspberry Pi OS Bullseye includes major changes to how DPI display drivers work. If you're using an image dated 04/04/2022 or later, it will come with Hyperpixel drivers baked in and you don't need to run the installer. You can set up display and touch by adding a few lines to your boot/config.txt:


PSA: HyperPixel 4 (Square & Rectangular) on Raspberry Pi OS 2022-04-04


If you're using Raspberry Pi OS Buster/Legacy (or an earlier version), you can use our one-line-installer to configure your Pi properly for HyperPixel 4.0 and to enable the touch screen on the touch version. Note that you'll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you follow our guide on how to set your Pi up headlessly.


Open a terminal, and type curl https://get.pimoroni.com/hyperpixel4 | bash to run the one-line installer and set your HyperPixel 4.0 up.


Want to use your Hyperpixel as a display for OctoPrint or Octodash? Check out Lost In Tech's video on how to set it up!

Notes

  • Dimensions:  75x80x8.9mm (WxHxD, depth includes header and display).

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare